Mobile version

Level-2Plus Wave products: New calibration of Jason-3 against in-situ data 

RELEASE :  

the 29 November 2022 
System v3.0 

The waves of the reference mission are calibrated against in-situ data over 4 years of data. The Level-2Plus waves of the other missions are calibrated on this reference mission corrected by buoys.
Currently the L2P wave products (up to version 2) were intercalibrated on Jason-3 and then a linear fit, determined by Queffeulou and Croizé-Fillon (2017) between Jason-2 and in-situ data, was applied to calibrate all the missions on the in-situ data. Nevertheless, comparison of L3 wave products (which use L2P wave products as input) with buoys have shown that the L2P/L3 wave products overestimate the swh. For L2P wave products version 3 a new absolute calibration between the reference mission and in-situ data will be used. In 2022, Jason-3 was calibrated against in-situ data, and a new lookup table has been produced by Dodet and Piollé  (2021). This new absolute calibration replaces the old linear fit determined by Queffeulou and Croizé-Fillon (2017). There are two advantages to this new calibration:  

  • the first is that as there was not enough data for Jason-3, the former calibration had been done on Jason-2 mission and used for Jason-3. Now Jason-3’s record is sufficiently long to produce its own, independent calibration.   
  • the second is that a lookup table is sensitive to non-linearities in the correspondence between the in-situ and altimetric measurements, whereas the linear function by definition was not (figure 1 below). 

Although Sentinel-6a is the new reference mission, until such a time as a sufficiently long record exists to permit a new calibration, it will be cross-calibrated with Jason-3 the same as any other secondary mission. However future missions that cannot be cross-calibrated with Jason-3 will be cross-calibrated with Sentinel-6a (which is itself cross-calibrated with Jason-3, which in turn has been calibrated against in-situ data). 

The new absolute calibration leads to differences from the preceding one which depend on the mission. For example, Figure 2 shows the regional differences for Sentinel-3A. We can see an impact for low and high waves. A more exhaustive validation is done in section VI of the QUID (https://catalogue.marine.copernicus.eu/documents/QUID/CMEMS-WAV-QUID-014-001.pdf) to present and assess the quality of the new calibration.
 

CALIBRATION PERFORMANCES :

For validation purposes, the L3 wave products (which use the L2P wave products as input) are compared to buoys.

The new calibration produces a lower bias for every mission, and a lower RMSE.  Sometimes the scatter index is higher with the new calibration, however it has been noted that this measure (and the RMSE) is not always reliable, because the mean and scatter are partially linearly dependent (Mentaschi et al., 2013).  The HH index is a more reliable indicator for validation purposes (Mentaschi et al, 2013), so it is included here as well, and it unambiguously favours the new calibration over the old one.
 

 

DATA INFORMATIONS :

The switch to the new absolute calibration has been done on November 29. The new files are available in the same folder as the current operational one with no change in the format or nomenclature. Only the global attribute “product_version” will change from 2_0 to 3_0

L2P wave/wind handbook: https://www.aviso.altimetry.fr/fileadmin/documents/data/tools/hdbk_L2P_WAVE_S3_S6.pdf 


References:
Dodet, G. and Piollé, J-F. (2021): Calibration of Level 2 Jason-3 GDR-F significant wave heights against in-situ measurements. Technical Report (Ifremer).
Queffeulou P. and Croizé-Fillon D. (2017): Global Altimeter SWH Data Set, version 11.4, February 2017. Technical report Ifremer. ftp://ftp.ifremer.fr/ifremer/cersat/products/swath/altimeters/waves/documentation/altimeter_wav e_merge__11.4.pdf  
Mentaschi, L., Besio, G., Cassola, F., & Mazzino, A. (2013). Problems in RMSE-based wave model validations. Ocean Modelling, 72, 53-58.

EnglishFrançais
Rss feedsContactPartnersFAQLexiconLegal noticePersonal Data Protection PolicyMobile
You must enable cookies in your browser preferences to save the modifications
You are using an older version of Internet Explorer, please update to take full advantage of Aviso+ features

Customize the home page

View all widgets
Reduce display
Public profile
User profile

Select/Deselect widgets

Discover AVISO+

Customizable home, reading tools, products search guide, etc.. Discover step by step the features of the new site AVISO+.

Customizable homepage

This home page is composed of blocks called "widgets".

Rearrange the blocks with a "Click & Drop".

Hide a widget with the cross at the top right. Reset or add a widget with the "wrench" icon. The "User" and "Public" profiles offer a predefined organization.

All the modifications are automatically saved as cookies on your machine so as to enable you to have your own specific AVISO+.

Reading tools

Ease your reading by choosing the page background colour (black/white) and/or by modifying the font size.

Browsing menu and breadcrum trail

To ease your browsing through AVISO+, you can use at any time the main banner items with the interactive submenus or use the browsing menu on the left side of the screen (it is open by default). For more readiness of the page contents, you can fold and unfold the browsing menu by clicking on the tab. At any time you can know where you are thanks to the browsing menu or the breadcrum at the top of the page.

Products search guide

The first submenu of the "Data" banner item leads you to a new search form enabling you to find quickier the product that suits your needs. The list of results is updated according to your selection criteria.

AVISO+ Multimedia

The first submenu of the "Multimedia" banner item leads you to AVISO+ collections of images and videos linked to altimetry and its applications. Have a nice visit!