Mobile version

KaRIn: Ka-band Radar Interferometer

KaRIn (Ka-band radar Interferometer) is a new class of altimeter, taking into account all the experience of previous missions (altimetry, but also SAR sensors), proposing with brand-new capabilities of measuring surface heights. 

The primary SWOT instrument is an interferometric altimeter which has a rich heritage based on 
(1) the many highly successful ocean observing radar altimeters, 
(2) the Shuttle Radar Topography Mission, 
and
(3) the development effort of the Wide Swath Ocean Altimeter (WSOA).

KaRIn is a near-nadir (1-4° look angles) swath-based instrument measuring the highly reflective water surface. The look angles at the altitude of the satellite entail swath coverage of about 120 km (from 10 to 70 km in cross-track distance on both sides of the nadir track). It will make measurements at Ka-band (35.75 GHz) with two Ka-band synthetic aperture radar (SAR) antennae at opposite ends of a 10-m boom. 
Interferometry SAR processing of the returned pulses yields a 5 m azimuth and 10 m to 70 m range resolution, with instantaneous elevation precision of 50 cm. Spatial averaging over areas of 1 km2 will improve this elevation precision to less than 2 cm.

 

KaRIn will provide continuous mapping operating, since instrument switch-on.

See Techniques>Altimetry page dedicated to altimeter-interferometer for more information on how it is working.

To form the required baseline between the two antennae, KaRIn will deploy two 5-m-long and 0.25-m-wide reflectarray antennas on opposite ends of a boom. Both antennas can technically transmit and receive radar pulses, but in the normal operation, only one will transmit (emit), and both will receive. The interferometer is a dual-swath system, alternatively illuminating the left and right swaths on each side of the nadir track. This is accomplished by an offset dual-feed design operating with orthogonal linear polarizations (V and H polarizations), which enables the emitting reflectarray antenna to generate two separate beams, one for each polarization, and thus enabling to discriminate from which swath the reflection is coming when receiving it back.

The KaRin instrument consists of:

The KaRIn Digital Electronics Subsystem (KDES):

The unit receives KaRIn commands from the spacecraft (S/C) and DORIS data (for altitude and navigation information) via the bus and sends KaRIn telemetry to the spacecraft via the same interface, acquires and packetizes telemetry from the rest of the instrument. It also receives and digitizes the echo information from the Radio Frequency Unit (see below). The KDES controls the radar hardware (Radio Frequency Unit, High Power Amplifier, alignment). To limit the data rate transmitted to the ground, the KDES converts the digitized data to interferograms. The data is transmitted to the solid state recorder at a maximum rate of about 360 Mbps.

 

The Radio-Frequency Unit (RFU)

It is made of all the analog components needed to modulate/demodulate, amplify and convert in frequency the chirp reference signal up to the High-Power Amplifier. The two main subsystems which form the RFU are the Duplexer, which is the switching matrix of the Radio Frequency signals and the HyperBox, which implements all other functions of the RFU : Pulses generation/emission & Echoes reception / Ka band up & down conversion.

 

The HPA (High Power Amplifier)

The HPA amplifies the chirped Radio Frequency signal sent by the RFU to 1500 W for transmission to the ground. The HPA consists of an Extended Interaction Klystron (which amplifies the low power radar signal), a JPL-built High Voltage Power Supply and a NASA-provided High Power Isolator/Filter. The HPA is block-redundant due to the criticality of this equipment. 

Deployable Antenna Assembly

It is a high precision, high stiffness, and stable deployable structure which allows the radar reflector arrays to be perfectly positioned in relation to the sources mounted on the supporting structure. The assembly consists of an integrated Mast Assembly (IMA) and an Integrated Reflector Array (IRA). It shall be as rigid as possible to guarantee a stabilized baseline. It is mostly built of carbon composite parts. The Integrated Reflector Array includes an alignment mechanism which can correct the pitch misalignment between the two reflectarrays.

The KaRIn Inertial Reference Unit (Gyro)

KaRIn includes a high-performance Inertial Reference Unit (IRU) to measure the orientation of the mechanical baseline. Having a stable orientation was already important with nadir altimeters; it is even more important with Swot since stability is required in the 3 dimensions.
 The unit is part of a flight-proven product line. It is a fiber optic gyro, sensing the angular rate using an optical signal traveling through a 5 km coil of optical fiber. There is no moving part. Optical fiber is available with very long life. The IRU has a built-in fault tolerance – four entirely independent channels, any three of which are sufficient. 

KaRIn System parameters

Parameter Value
Center frequency 35.75 GHz 8.4 mm wavelength
TX Bandwidth 200 MHz 0.56 % bandwidth
TX Pulse length 5.7 us Capability to operate within 3 - 9 us
Pulse Repetition Frequency (average) 2 x 4420Hz Varies by < 5% along the orbit
Peak Transmit Power (EOL) 1500W
Physical Baseline Length 10 m
Antenna size 5 mx 0.25 m
Boresight Look Angle +/- 2.65 deg Swath look angles -0.65° to 3.9°
Polarization, Right Swath VV Alternating polarizations between
Polarization, Left Swath HH consecutive pulses to 'illuminate both swaths.
EnglishFrançaisEspañol
Rss feedsContactPartnersFAQLexiconMobile
You must enable cookies in your browser preferences to save the modifications
You are using an older version of Internet Explorer, please update to take full advantage of Aviso+ features

Customize the home page

View all widgets
-->
Reduce display
Public profile
User profile

Select/Deselect widgets

Discover AVISO+

Customizable home, reading tools, products search guide, etc.. Discover step by step the features of the new site AVISO+.

Customizable homepage

The new home page is composed of blocks called "widgets".

Rearrange the blocks with a "Click & Drop".

Hide a widget with the cross at the top right. Reset or add a widget with the "wrench" icon. The "User" and "Public" profiles offer a predefined organization.

All the modifications are automatically saved as cookies on your machine so as to enable you to have your own specific AVISO+.

Reading tools

Ease your reading by choosing the page background colour (black/white) and/or by modifying the font size.

Browsing menu and breadcrum trail

To ease your browsing through AVISO+, you can use at any time the main banner items with the interactive submenus or use the browsing menu on the left side of the screen (it is open by default). For more readiness of the page contents, you can fold and unfold the browsing menu by clicking on the tab. At any time you can know where you are thanks to the browsing menu or the breadcrum at the top of the page.

Products search guide

The first submenu of the "Data" banner item leads you to a new search form enabling you to find quickier the product that suits your needs. The list of results is updated according to your selection criteria.

AVISO+ Multimedia

The first submenu of the "Multimedia" banner item leads you to AVISO+ collections of images and videos linked to altimetry and its applications. Have a nice visit!